| IS 207 : 1964 Specification for gate and shutter hooks and eyes (revised) |
| IS 451 : 1999 Specification for technical supply conditions for wood screws (third revision) |
| IS 554 : 1999 Specification for pipe threads where pressure-tide joints are made on the threads – Dimensions, tolerances and designation (fourth revision) |
| IS 723 : 1972 Specification for steel countersunk head wire nails (second revision) |
| IS 724 : 1964 Specification for mild steel and brass cup, ruler and square hooks and screw eyes (revised) |
| IS 725 : 1961 Specification for copper wire nails (revised) |
| IS 730 : 1978 Specification for hook bolts for corrugated sheet roofing (second revision) |
| IS 1120 : 1975 Specification for coach screws (first revision) |
| IS 1363 Specification for hexagon head bolts, screws and nuts of product grade C |
| (Part 1) : 2002 Hexagon head bolts (Size range M5 to M64) (fourth revision) |
| (Part 2) : 2002 Hexagon head screws (Size range M5 to M64) (fourth revision) |
| (Part 3) : 2002 Hexagon nuts (Size range M5 to M64) (fourth revision) |
| 1364 Specification for hexagon head bolts,screws and nuts of product Grades A and B |
| (Part 1) : 2002 Hexagon head bolts (Size range M1.6 to M64) (fourth revision) |
| (Part 2) : 2002 Hexagon head screws (Size range M1.6 to M64) (fourth revision) |
| (Part 3) : 2002 Hexagon nuts (Size range M1.6 to M64) (fourth revision) |
| (Part 4) : 2003 Hexagon thin nuts (chamfered) (Size range M1.6 to M64) (fourth revision) |
| (Part 5) : 2002 Hexagon thin nuts (unchamfered) (Size range M1.6 to M10) (fourth revision) |
| (Part 6) : 2002 Hexagon nuts, style 2 |
| IS 1365 : 2005 Slotted countersunk flat head screws (Common head style) – Product Grade A (fourth revision) |
| IS 1366 : 2002 Specification for slotted cheese head screws (third revision) |
| IS 1367 Specification for technical supply conditions for threaded steel fasteners |
| (Part 1) : 2014 Introduction and general information (fourth revision) |
| (Part 2) : 2002 Product grades and tolerances (third revision) |
| (Part 3) : 2002 Mechanical properties and test methods for bolts, screws and studs with full loadability (fourth revision) |
| (Part 5) : 2002 Mechanical properties and test methods for set screws and similar threaded fasteners not under tensile stresses (third revision) |
| (Part 6) : 1994 Mechanical properties and test methods for nuts with specified proof loads (third revision) |
| (Part 7) : 1980 Mechanical properties and test methods for nuts without specified proof loads (second revision) |
| (Part 8) : 2014 Mechanical and performance properties for prevailing torque type steel hexagon nuts (fourth revision) |
| (Part 9/Sec 1) : Surface discontinuities, Section 1 1993 Bolts, screws and studs for general applications (third revision) |
| (Part 9/Sec 2) : Surface discontinuities, Section 2 1993 Bolts, screws and studs for special applications (third revision) |
| (Part 10) : 2002 Surface discontinuities on nuts (third revision) |
| (Part 11) : 2002 Electroplated coatings (third revision) |
| (Part 12) : 1981 Phosphate coatings on threaded fasteners (second revision) |
| (Part 13) : 1983 Hot dip galvanized coatings on threaded fasteners (second revision) |
| (Part 14/Sec 1) : 2002 Mechanical properties of corrosion resistance stainless stainless steel fasteners, Section 1 Bolts, screws and studs (third revision) |
| (Part 14/Sec 2) : 2002 Mechanical properties of corrosion resistance stainless stainless steel fasteners, Section 2 Nuts (third revision) |
| (Part 14/Sec 3) : 2002 Mechanical properties of corrosion resistance stainless stainless steel fasteners, Section 3 Set screws and similar fasteners not under tensile stress (third revision) |
| (Part 16) : 2002 Designation system and symbols (third revision) |
| (Part 17) : 2005 Inspections, sampling and acceptance procedure (fourth revision) ( |
| Part 18) : 1996 Packaging (third revision) |
| (Part 19) : 1996 Axial fatigue testing of bolts, screws and studs |
| (Part 20) : 1996 Torsional test and minimum torques for bolts and screws with nominal diameters 1mm to 10 mm |
| IS 1929 : 1982 Specification for hot forged steel rivets for hot closing (12 to 36 mm diameter) (first revision) |
| IS 2016 : 1967 Specification for plain washers (first revision) |
| IS 2155 : 1982 Specification for cold forged solid steel rivets for hot closing (6 to 16 mm diameter) (first revision) |
| IS 2269 : 2006 Hexagon socket head cap screws (fifth revision) |
| IS 2585 : 2006 Specification for square head bolts, screws and square nuts of product grade C (second revision) |
| IS 2609 : 1972 Specification for coach bolts (first revision) |
| IS 2643 : 2005 Pipe threads where pressure-tight joints are not made on the threads – Dimensions, tolerances and designation (third revision) |
| IS 2687 : 1991 Specification for cap nuts (second revision) |
| IS 2769 : 1969 Sizes for squares and square holes for general engineering purposes (first revision) |
| IS 2907 : 1998 Specification for non-ferrous rivets (first revision) |
| IS 2998 : 1982 Specification for cold forged steel rivets for cold closing (1 to 16 mm diameter) (first revision) |
| IS 3063 : 1994 Specification for fasteners single coil rectangular section spring lock washers (second revision) |
| IS 3121 : 1981 Specification for rigging screws and stretching screws (first revision) |
| IS 3468 : 1991 Specification for pipe nuts (second revision) |
| IS 3640 : 1982 Specification for hexagon fit bolts (first revision) |
| IS 3757 : 1985 Specification for high strength structural bolts (second revision) |
| IS 4206 : 1987 Dimensions for nominal lengths, and thread lengths for bolts, screws and studs (first revision) |
| IS 4762 : 2002 Specification for worm drive hose clips for general purposes (second revision) |
| IS 5369 : 1975 General requirements for plain washers and lock washers (first revision) |
| IS 5370 : 1969 Specification for plain washers with outside diameter 3 × inside diameter |
| IS 5372 : 1975 Specification for taper washer for channels (ISMC) (first revision) |
| IS 5373 : 1969 Specification for square washers for wood fastenings |
| IS 5374 : 1975 Specification for taper washers for l-beam (ISMB) (first revision) |
| IS 5624 : 1993 Specification for foundation bolts (first revision) |
| IS 6113 : 1970 Specification for aluminium fasteners for building purposes |
| IS 6610 : 1972 Specification for heavy washers for steel structures |
| IS 6623 : 2004 Specification for high strength structural nuts (second revision) |
| IS 6639 : 2005 Specification for hexagon head bolts for general steel structures (first revision) |
| IS 6649 : 1985 Specification for hardened and tempered washers for high strength structural bolts and nuts (first revision) |
| IS 6733 : 1972 Specification for wall and roofing nails |
| IS 6736 : 1972 Specification for slotted raised countersunk head wood screws |
| IS 6739 : 1972 Specification for slotted round head wood screws |
| IS 6760 : 1972 Specification for slotted countersunk head wood screws |
| IS 8033 : 1976 Specification for washers with square hole for wood fastenings |
| IS 8412 : 1977 Specification for slotted countersunk head bolts for steel structures |
| IS 8822 : 1978 Specification for slotted mushroom head roofing bolts |
| IS 8869 : 1978 Specification for washers for corrugated sheet roofing |
| IS 8911 : 2005 Countersunk slotted raised head screws (common head style) – Product Grade A (first revision) |
| IS 10102 : 1982 Specification for technical supply conditions for rivets |
| IS 10238 : 2001 Specification for step bolts for steel structures |
| IS 12427 : 2001 Specification for threaded steel fasteners – hexagon head transmission tower bolts (first revision) |
List of Indian Standard Code Books Related to Threaded Fasteners, Rivets and Nails
September 7, 2019
